#! /bin/sh
# Copyright (c) University of Cambridge, 1995 - 2007
# See the file NOTICE for conditions of use and distribution.
# Except when they appear in comments, the following placeholders in this
# source are replaced when it is turned into a runnable script:
#
# CONFIGURE_FILE_USE_NODE
# CONFIGURE_FILE
# BIN_DIRECTORY
# EXIWHAT_PS_CMD
# EXIWHAT_PS_ARG
# EXIWHAT_KILL_SIGNAL
# EXIWHAT_EGREP_ARG
# EXIWHAT_MULTIKILL_CMD
# EXIWHAT_MULTIKILL_ARG
# RM_COMMAND
# This file has been so processed.
# Shell script for seeing what the exim processes are doing. It gets rid
# of the old process log, then sends SIGUSR1 to all exim processes to get
# them to write their state to the log. Then it displays the contents of
# the log.
# The following lines are generated from Exim's configuration file when
# this source is built into a script, but you can subsequently edit them
# without rebuilding things, as long are you are careful not to overwrite
# the script in the next Exim rebuild/install. However, it's best to
# arrange your build-time configuration file to get the correct values.
rm=/bin/rm
# Some operating systems have a command that finds processes that match
# certain conditions (by default usually those running specific commands)
# and sends them signals. If such a command is defined for your OS, the
# following variables are set and used.
multikill_cmd=killall
multikill_arg=exim
# In other operating systems, Exim has to use "ps" and "egrep" to find the
# processes itself. In those cases, the next three variables are used:
ps_cmd=/bin/ps
ps_arg=ax
egrep_arg='/exim( |$)'
# In both cases, kill_arg is the argument for the (multi)kill command to send
# SIGUSR1 (at least one OS requires a numeric value).
signal=-USR1
# See if this installation is using the esoteric "USE_NODE" feature of Exim,
# in which it uses the host's name as a suffix for the configuration file name.
if test "x$1" = x--version
then
echo "`basename $0`: $0"
echo "build: 4.94.2"
exit 0
fi
if [ "" = "yes" ]; then
hostsuffix=.`uname -n`
fi
# Now find the configuration file name. This has got complicated because
# CONFIGURE_FILE may now be a list of files. The one that is used is the first
# one that exists. Mimic the code in readconf.c by testing first for the
# suffixed file in each case.
set `awk -F: '{ for (i = 1; i <= NF; i++) print $i }' <<End
/etc/exim.conf
End
`
while [ "$config" = "" -a $# -gt 0 ] ; do
if [ -f "$1$hostsuffix" ] ; then
config="$1$hostsuffix"
elif [ -f "$1" ] ; then
config="$1"
fi
shift
done
# check we have a config file
if [ "$config" = "" -o ! -f "$config" ]; then
echo Config file not found.
exit 1
fi
# Determine where the spool directory is. Search for an exim_path setting
# in the configure file; otherwise use the bin directory. Call that version of
# Exim to find the spool directory. BEWARE: a tab character is needed in the
# first command below. It has had a nasty tendency to get lost in the past. Use
# a variable to hold a space and a tab. This is less likely to be touched.
st=' '
exim_path=`grep "^[$st]*exim_path" $config | sed "s/.*=[$st]*//"`
if test "$exim_path" = ""; then exim_path=/usr/sbin/exim; fi
spool_directory=`$exim_path -C $config -bP spool_directory | sed "s/.*=[ ]*//"`
process_log_path=`$exim_path -C $config -bP process_log_path | sed "s/.*=[ ]*//"`
# The file that Exim writes when sent the SIGUSR1 signal is specified by
# the process_log_path option. If that is not defined, Exim uses the file
# called "exim-process.info" in the spool directory.
log=$process_log_path
if [ "$log" = "" ] ; then
log=$spool_directory/exim-process.info
fi
# Now do the job.
$rm -f ${log}
if [ -f ${log} ]; then
echo "** Failed to remove ${log}"
exit 1
fi
# If there is a multikill command, use it. On some OS this command is called
# "killall" (Linux, FreeBSD). On Solaris it is called "pkill". Note that on
# Solaris, "killall" kills ALL processes - this is the System V version of this
# command, and not what we want!
if [ "$multikill_cmd" != "" ] && type "$multikill_cmd" >/dev/null 2>&1; then
$multikill_cmd $signal "$multikill_arg"
# No multikill command; do it the hard way
else
$ps_cmd $ps_arg | \
egrep "$egrep_arg" | \
awk "{print \"kill $signal \"\$1}" | \
uniq | sh
fi
sleep 1
if [ ! -s ${log} ] ; then echo "No exim process data" ;
else sort -nu ${log} ; fi
# End of exiwhat
Mini Shell